Information needed for rotor commutator fusing machine inquiryIt will be better if customer could send us detailed drawing including below information.1. Rotor assemble drawing: wire diameter2. Commutator drawing3. Shaft drawing4. Required productivity5. Other technical requirementIf possible, it will be better if customer can send us samples.

There are several type of coil inserting machines, automatic type, semi-auto type and horizontal type. It might be confusing for customer to choose the correct machine.Normally we recommed to use fully automatic type coil inserting machine for stators with a high production, It can automatically insert coil and wedge into stator slots, so as to save labor force and time. For stators with many mode...

Information needed for Automatic BLDC Stator Coil Winding Machine inquiryIt will be better if customer could send us detailed drawing including below information.1. Stator drawing2. Stator winding drawing3. Winding distribution drawing4. Other technical requirementIf possible, it will be better if customer can send us samples.

Information needed for coil winding machine inquiryIt will be better if customer could send us detailed drawing including below information.1. Stator drawing2. Stator winding drawing3. Winding distribution drawing4. Other technical requirementIf possible, it will be better if customer can send us samples.

Information needed for coil winding machine inquiryIt will be better if customer could send us detailed drawing including below information.1. Stator drawing2. Stator winding drawing3. Winding distribution drawing4. Other technical requirementIf possible, it will be better if customer can send us samples.

Material needed for stator winding machine1. Stator drawing2. Stator application3. Stator wound sample4. stator production requirement5. Copper wire and unwound stator

Information needed for Armature(Rotor) Winding Machine inquiryIt will be better if customer could send us detailed drawing including below information.1. Rotor lamination drawing2. Rotor assemble drawing3. Rotor stack drawing4. Rotor winding diagram drawing: with rotor wire diameter and turn number5. Commutator drawing6. Required productivity7. Other technical requirementIf possible, it will be be...

Question: In paper insertion machine some time machine is running directly.See attached video.Some problem display.Answer:Thanks for the video and problem description, Would you please also inform below information to us?1. In which speed the machine running directly, speed1, speed2 or speed 3?2. The speed vibrate some time or every time? Question: 1. In third speed2. Every timeAnswer: Please ch...

We study your datas and found that actually both machines have no problem with the balance armature,this means both machine are ok for balancing.Only unbalance aramture has some difference which is not much matter.We give some suggestions as below:Issue 1:New machine has higher test value.1.Change the supporting part of new machine to same as old machine's ceramic bar. (See attached photo)Note:Th...

Question: Plese send the quotation of rotor with the rotor injected,Answer: We need the drawing of injected rotor because we need to know the aluminium ring height, width and if the pin required or not, all these are related the aluminium volume. The volume different, then the price is different. Please kindly provide

Question: Wedge insertion machine.In this mechanical setting is not proper.We can not maintain this part because it can not be opened..Slider is sticking inside.Answer:There are 3 bolt on this part. 1st loosen the bolt then by using hand wheel move the slider, if the slider move clearly then again tighten the bolts

The are two methods to slove hook missing problem:Put on the armature, have a check if the position of armature and hook tooling is alignment,Method 1: Adjust the hook tooling a little clockwise or anti-clockwise (based on the situation) after loosening the screws;Method 2: Adjust the indexing value with 1 degree plus or minus( based on the situation) It means each time 1 degree, and the formula...

Question: We found the second amplifier show'AL 20'Solution:The middle amplifier is for right flier, the problem might come from machine mechanical parts blocked or phase loose or short circuit,Please follow below steps to check,1. Switch off the power, then try to rotate the right flier motor with your hand, in normal condition, it should be smooth, If you felt there is resistance, please ch...

Question: I check the machine start to end 1) First machine switch on 2) Do the balancing new pieces , up 12 pieces is ok 3) After 13 pieces machine become problem. Motor will no run ( switch or food switch ) to press4) After the machine will switch off .5) Then machine switch on . do the balancing motor will run .up to become problem Thanks for your detail description...

For Litz wire (Fil de Litz) winding machine, you may consider 3M method for save cost if 3M is cheaper than glue in your country,For 3M method, you only need one set fixture (bottom fixture and up fixture) which is USD110, the process is as below,The video http://..........com/u81/v_OTY1MjU1MTA.html will help you try to understand the process1. Put on the tooling to the machine 2. Put on the bot...

Question: We are getting ERROR 21 in Armature Winding machine ND-LAW-5B. Can you please send us the ERROR LIST and the diagnostic procesdureSolution:I enclosed the instruction manual, please check,Error21 is poor contact of communication,Your could check the servor motor's wire, encoder line of amplifier on the back side of the machine (cabinet)Then well connect them,

Question: We are facing problem in commutator turning machine.See the attached video (Run not work)Solution: Please re-connect the wire for touch screen and PLC connection:1. Manually loosen the screw for fixing the wire, and make the wire well connected,2. After that, tighten the screw,Question: Now the same problem repeated.Loosen the screw & connection two time & tighten but problem is as it i...

Indution cooker disk is related to the induction cooker power because there should be enough space for the litz wire to go through,and also please consider the process of producting the whole product,

Question: 1. cycle stop function. we are tighten all electrical connection & Check but the cycle stop meter working few times then automatic not working. The power coating function ok but vibration continue. 2. Voltmeter & ammeter on Panel not working. The heating Ok but on panel voltmeter & ammeter not showing.Solution:1. Please change the two relay KT6 and KT3 ( time relay KT6 and powder coa...

Question: In our stator winding, all days we used 23.5 & 23 SWG aluminum wire and have no problems. Last couple of weeks we introduced 22 SWG Aluminum wire which got cut during Loop taking at middle of winding. We wind 170 + 30 Turns in stator. After 170 turns we need to take Loop wire, then wind 30 turns. This is normal Operation. In NIDE stator winder after 170 turns of wind while machine taking...

1. Check if the marked place, out ring part should be 1 to 2mm on the outside of the inner ring part, If you didn't adjust it before, don't change it2. Please add the hang shifting angle a little big, add 2 to 5 and check the result,

The material H13 is material for good quality bakelite, The Electric Heating Pipe,temperature controller Oven,the injection machine need to work with mold,

Question: 1. The nozzle touch the wire 2. The indexing is not in home positionAnswer:The machine problem may caused by two reason,1. The indexing home position is not in original home position2. The needle is protected by machine protectionTo slove the problem, please follow below step:1) Turn to 'Manul control', press 'Indexing clockwise ' then turn to 'Auto control' to see if...

Question: COMMUTATOR TURNING MACHINE ND-WGK-2X Touch screen don't response and blink when 'Data set', Solution:Please re-connect the wire for touch screen and PLC connection:1. Manually loosen the screw for fixing the wire, and make the wire well connected,2. After that, tighten the screw,

Question:There is an intermittent problem in Balancing machine. The machine is working normally and during the normal process, all of a sudden it shows the following value: Left side 35 and Right Side 65. After Switching OFF and restarting, then it is working normally and the values are decreasing.Why this inconsistency problem?Answer:The intermittent problem might come from the not well ground co...

Question:Our Nide turning machine is showing the error message as shown in the below screen shots and not able to reset the errorSystem screen does not respond to change the below shown value ( highlighted by a circle in the picture ) and the machine is not coming to home position Kindly help to resolve this issueSolution:Based on the photo information, we found below problem,1. The rotor No is 50...

In commutator hostacking machine, collet is not broken, only shaft holding inner dia is increased.Before the collet broken, did you check if the V holder was in proper position and wheather the armature and V holder base are working properly?Please check the V holder and adjust it in proper position, then the collet won't be worn out easily,Loose size is not so big .Some time Armature not moving ...

Question: There will two servo driver showed 'Err 11', and the screen showed 'Err11' Solution: The whole circuit is General power supply --- General air switch --- Transformer --- Fuse --- Separate air switch ,Please follow below step to check, 1. Please measure the three terminal of air swith which is at lefft side of the amplifier, Both amplifier gave out Err 11, measure their left side ...

Question: In commutator turning M/C cutter is not taking second cutAnswer: We checked the video and paramater, as there is little difference in 1 and 2 you set,Plese set the 2 from 3.080MM to 3.090MM or 3.100MM,

Commutator turning machine PLC Mitsubishi show E003 and the drive is flickering 1 and 2.Please follow below steps to set the P8 as 0.5, then the problem will be sloved, 1. Press pu/ext, the pu indicator will light,2. Press MODE, the P0 will appear in screen, then rotate the switch to the P8, some data will appear in screen, rotate the switch to set the data as 0.5, press SET to confirm the se...

Theorily speaking,coating thickness is adjustable by setting temperature and coating period. Practically speaking, it has direct relationship with the powder property. If the powder is limited to fast curing property, the coating thickness could be adjusted too but the coating suface is not perfect (the surface might be a little rough).

z axis value (*******) can not be changed,single action mode z axis can move but value cannot be changedAdjust the commutator turning machine to home position, as the process when you change a cutter

We Turn off the machine, 5 minutes later, turn on again, then i put on 1 piece of armature, long time press the foot pedal but not run the motor.Motor not run while initially turn on the machine (at foot pedal press condition) ? From your description, we detect it is the driver problem,

Problem: Servo drive is not changing its figure, normally it should be a data, not a code,It is showing AL....37(continue on - off,on - off).It is flickering.NO changes when machine is running There are four press button on the servo motor driver, please follow below steps to set the parameter:1. Press the first button, P 00 will show in the screen2. Press the fouth button, then press the fouth b...

The winding machine's monitor doesn't respond when turning on but shows only data, there is nothing I can select as there is on menu bar shown,Please check the situation of 6 lights POWER、RUN、ERR/ALM、INT、BKUP、PRPHL,Whether they are on or off or flickering, if they are on, what is the color, red or yellow? Please take picture and describe sperately for the 6 lights. And please check the two parts ...

Please check the parameter setting,Flier short swing should be around 30000, and speed up running speed of flier is around 800

When design the paper size, we consider the armature sample, the armature lamintation and paper sample from customer, and give a suggestion on paper size, such as insulation paper width and thickness, Then when you use the machine, please follow the insulation paper size we suggested.The whole set tooling including paper press wheel, the forming block, the plate for paper going though,the base for...

Hydraulic oil no is 20#,please clear the rest oil in tank,and add clean 20 lubricating oil,then start machie,put in action no 100 to let the oil pump run about 1 minute to let the oil go through fully,only after that could run the machine.

Please input oil dipping action no.in the touching screen, open the electric cabinet. Taking universal electric meter to measure the voltage of contactor---wire UL,VL,WL alternatively. Provided their value is similar and within 380-400V. It verifies the oil pump is ok. Otherwise the pump was burnt.----pls replace it. If Oil pump is ok, pls refer to fuse. From right to left, pls use universal elec...

To design a stator impregnation machine, you should inform your Max stator OD and stack height, Max wound stator height (Including the overhanging height), the varnish class (curing temperature and time),Also some country is lack of electric, you would like the use diesel instead of electric,